(I showed you how to do that in my Frozen Beauty tut if you need to see it in screenshots)
Selections None
Now move this weaver selection up the LP so it's just under the rectangle
layer you selected
Back to the next complete Weaver layer
And going steadily - move it UP on the tag area so it's no longer
'lining up' with the previous weaver layer
and you're focusing on the top horizontal rectangle area
I moved mine diagonally up to the right and then
placed where I thought it looked good within the space
Then - once you're happy with placement
Repeat the Selection Invert Delete as you did for the previous weaver layer
Again, once you're done - move this weaver layer so it's directly under the
template layer you used as your guide in the LP
Finally for this bit - yup, you guessed it!
Please do the same for the bottom rectangle layer
Move, place, Select Weaver layer, Invert, Delete, move up the LP
Your tag should be taking shape and looking a bit like this...
As you can see, the weaver fills are not aligned and they're
different in each area - all fills are directly under their
corresponding template "frame" in the LP (Layer Palette)
Looking a bit like that?
Marvellous!
On we go...
Actually - I need a cup of tea.
I'll be back in ten minutes...
Back!
Right - so now then
Unhide your original Wallpaper layer
And go to Crop Tool
Then along the top, choose Snap Crop Rectangle to: and choose the
third one along called Merged Opaque - before you hit tick, check the "new"
dimensions. Should be the size that you saved your template at -
mine showed 750 by 530 - yup! tick!
Brilliant!
Now on this Wallpaper layer
Apply Millie's mask and resize the
Mask layer by 95%
Adjust, Sharpness, Sharpen the mask layer
Duplicate your larger Weaver rectangle layer section
Move it above the CU tube in the LP
Change the Blend Mode to Hard Light
then
go to Xero Graphics Greyscaler
and apply the default to the top Weaver Layer
So concentrating on this tag area
In the LP from top to bottom at this moment your
layers should be -
rectangle large frame layer
greyscaled weaver fill layer on Hard Light
close up tube
bottom weaver fill layer
If so - BOOM! Well done, taking shape beautifully!
If not...re-read that lot above and see if I've led you up the garden path
or perhaps we've missed a step hehe
Lovely!
Now, take the "girl" tube from your original (the smaller version)
C&P
Place within the area of the top horizontal rectangle layer
Drop this in the LP below the Hard Lit Greyscaled weaver fill so it's
sandwiched between the original coloured weaver fill piece and the
top one
Do an Invert Delete on the tube
Change the blend mode of the tube layer if you'd like
I changed to SOFT light
Selection None
Now, for the bottom right rectangle area, don't apply your tube at all
Instead, when you've greyscaled the top layer,
Apply Xero Fuzzifier on these settings
Now, crop your canvas to get rid of any excess tube layering that
may be left over from all that Wallpapering etc.
Don't think that there isn't any...there was on mine. It was lurking loL!
So, that's why I'm adding this bit in.
Crop your canvas and once you've done it resize your canvas
back to approx. 750 x 550 or so (this will allow you space for shadowing etc.)
C&P the tube once more
Resize at 40%
Place as liked or use mine for guidance if using same or similar
Sharpen if needed
and add a favourite finish of your choice then
Don't forget to drop shadow your tube with a good setting for being sat down
like she is
(I duplicated my tube
Adjust, Blur, Gaussian by 1 to the top layer
then applied Xero Greyscaler on default and
dropped the Opacity to 42
then on the bottom tube layer
Lokas Software - 3D Shadow on these settings*
*One difference - I changed the slider on Angle X to -3
as the feathers on her head made the shadow "touch" the outside
of the tag area and that would have meant a harsh crop.
And my tag is already big enough lol!
So, I reduced the angle a bit.
Click on the larger rectangle frame layer
Apply Effects, Texture Effects, TIles on these settings
Apply this to all of the rectangle frame layers
Extra: If you'd like to - you can "fill" some of the rectangles with
scrap elements if you'd like, shadow it all and then using your
saved Selections, do a Selection
Invert to delete any elements parts that underlay and stick out of the frame area
But, I kept it simpler for this tut and didn't do that bit
Then on each of the rectangle layers
Apply the Drop Shadow of 2, 2, 50, 2 Black
Time to tidy up ready for the end now?
OK - delete ANY excess layers we don't need anymore
I had a spare Weaver layer...just in case lol!
Don't need it - delete it
Once you've done that and are happy you've got all you need
Hide your tube layers and the mask layer
and the bottom Background White fill layer
then Merge Visible everything else to keep it neat and tidy.
Unhide all that's hidden once more
Add your Wording now
Choose a nice font - not handwriting, script or swashy,
choose either a serif or sans serif font
No Stroke, White fill
and type out some wording
I went for
"Forever in my Heart..."
Change to Raster
Add the same drop shadow we used
for the rectangle frames
then place in the LP
behind the tube
in the area of the bottom horizontal layer
and change the Blend Mode to something you like
I think I did Soft or Hard Light lol!
Now finally
In a scripty or handwriting font of choice
With no stroke and a Black fill
I added the chosen name for my tag (in my case, it's my lovely friend
Rachey who was the 2nd person to "follow" this blog hehe!)
Place the name where you like it
then if liked
Apply a Glow or Shadow of choice
(I applied Gradient Glow - Angelic Halo but I change the
colour settings to match my tag - then NO shadow - tip: when a loose glow
is applied, a shadow as well can look naff. But if a crisp glow is applied, the shadow can
be the finishing touch. Play around, see what look best for YOOOOOU)
Finally,
Add the artists copyright information, your licence information if needed
and of course, your tagger sign off if you use one.
Delete the White Background
Hit Shift and hold it down then hit D to duplicate the entire image
Layers Merge on the new one and save as a PNG
Then - Save your original tag image as a layered PSPImage
And you're done!
Thank you for trying this tut.
I'd love to see your results and add them to this page so if you do this tut